EOS D60 E

EOS D60 Firmware Update Version 1.0.4

What's new?

EOS D60 Firmware Version 1.0.4 resolves the following issues, which may occur in the RAW mode depending on shutter release timing:

1.	Thumbnail is black. *1
2.	Data is not written to CF card (or microdrive). *2
	*1	Only the thumbnail image is affected, there is no problem with the main image.
	*2	With EOS D60 cameras that have Firmware Version 1.0.0, 1.0.1 or 1.0.2 installed, in cases where data stored in the camera's buffer memory has not yet been written to the CF card or microdrive, that data will be written when the menu button is pressed, or when the shutter button is pressed halfway.

EOS D60 Firmware Version 1.0.4 can be used to update EOS D60 cameras with Firmware Version(s) 1.0.0, 1.0.1 or 1.0.2.

Before downloading the firmware update, please be sure to read the entire contents of this page.

Q & A of Firmware

Q:	Should all EOS D60 cameras with earlier firmware versions installed be updated to Firmware Version 1.0.4?
A:	Yes.

Q:	Are improvements from Firmware Version 1.0.2 also included ?
A:	Yes, they are. For your reference, Version 1.0.2 resolves the following issues which can occur depending on the camera settings, scene and shooting time. Underexposure may occur in low light situations when SI (Superimpose) display is ON. Duplicate file numbers may occur when more than 100 images are recorded per folder.

Q:	How do I check the camera's current firmware version number?
A:	Turn the Main Switch ON, and press the MENU button to display the menu. Turn the Quick Control Dial, and you will see the "Firmware Ver.1.0.x" at the end of the settings shown in yellow, which is the currently installed firmware version number. For more details , please refer to the instruction manual on pages 32, 33 and 121.

Q:	How do I update the EOS D60's firmware?
A:	Two methods of firmware updating are provided. Download the firmware file from this web site and install the update as shown in the updating procedure. Bring the camera to a Canon Service Center and have the firmware updated by the center. If you choose the latter method, contact a Canon Service Center in your region.

Do I need any special equipment to update the EOS D60's firmware?

The following equipment is necessary to update the EOS D60's firmware.

Battery Pack BP-511 (The battery pack must be fully charged.)
Compact Power Adapter CA-PS400 and DC Coupler DR-400
CF card (8MB or more)

In order to supply power to the camera, 1 or 2 is necessary. (AC power is recommended.

How do I copy the downloaded firmware file to the CF card?

Two methods of copying the downloaded firmware file are provided.

If you have a CF card reader or a PC card reader*, or a notebook type personal computer with a PC card slot*, please copy the firmware file included in the downloaded data a freshly formatted CF card.
* If you use a CF card with a PC card reader or a PC card slot, a PC card adapter is necessary.
If you do not have any of the above equipment, please connect the camera and a personal computer with a USB cable*, and copy the firmware file onto the CF card in the camera. For copying, "UploadFirmware**" (utility software) is included in the downloaded data.
* For USB connection, the interface cable IFC-200PCU enclosed with the camera is necessary.
** Macintosh version of UploadFirmware requires Mac OS 8.6 to 9.2.

Q:	I do not have the equipment necessary for the firmware update.
A:	Please contact a Canon Service Center in your region.

Q:	While copying the firmware, the word "ERROR" is shown on the display.
A:	The firmware updating procedure has failed. If you used battery pack BP-511, please change the power supply equipment to the compact power adapter CA-PS400 and the DC coupler DR-400, and try to update the firmware again. If the word "ERROR" still appears on the display after the update, or some problems are found during the update, please contact the Canon Service Center.

Equipment required for firmware update

Battery Pack BP-511 ( fully charged )
Compact Power Adapter CA-PS400 and DC Coupler DR-400
CF card (8MB or more)

Use either Battery Pack BP-511 or Compact Power Adapter CA-PS400 as power supply. (AC power is recommended.)

Preparation for EOS D60 firmware update

STEP 1: Format a CF card

Use a formatted CF card for installing the new firmware ( 8MB or more).

Be sure to carefully review the contents of the CF card before formatting. Insert the CF card into the EOS D60, and switch the Main Switch to Replay mode. Press "MENU" button and select the tools "Setup" menu. And then select "FORMAT" and then accept the confirmation to initialize the CF card.

STEP 2: Prepare Power Supply and/or Interface Cable

One of the following power supplies is necessary for firmware update.

Battery Pack BP-511 ( fully charged )
Or, Compact Power Adapter CA-PS400 and DC Coupler DR-400

Interface Cable IFC-200PCU is necessary if you prefer to connecting the camera to the PC and copying the firmware file to the CF card.

STEP 3: Download the EOS D60 firmware update procedure file (PDF file)

EOS D60 firmware update procedure is available in the PDF file at the end of this page.

Please download the PDF file and read the procedure carefully before firmware update.

STEP 4: Download the firmware from this page

Download the firmware update file that is suited to your computer's operating system.

The file is a self-extracting compressed archive. Double-click it for extraction.

After downloading and decompressing the file, verify that the folder contains the following files.

Windows® "EOSD60Firmware104E" folder	MacOS "EOSD60Firmware104E" folder

* Windows users may need to adjust their folder view setting to "see hidden files" in order to see all the files.

Please check the file size of the firmware before installation.

Firmware Update File

D60V104.fir

* Windows : Size in Property (993,858 bytes)
* Mac OS : Size in Information (993,858 bytes)

If the downloaded file size is different from the above, please download the firmware again.

Precautions

Use a fully charged Battery Pack BP-511 or dedicated Compact Power Adapter CA-PS400 for firmware update. (AC Power is recommended.)
Do not shut off the power during the firmware writing operation. A power failure during the firmware writing operation may disable the camera.
Do not open the CF card slot cover or press any camera buttons during the firmware writing operation.

EOS D60 firmware update procedures

(1) Copy the "D60V104.fir" file to the formatted CF card.

If you do not have any of the card reading devices,

Insert the CF card into the EOS D60, and connect it to the PC with Interface Cable IFC-200PCU.
Double-click the "UploadFirmware*" in the decompressed folder, and follow the instructions so that the "D60V104.fir" file can be copied onto the CF card in the EOS D60.

When you attempt to transfer the data to the CF card in the EOS D60 with the "UploadFirmware*" program, do not open the CF card slot cover, turn the Main Switch or turn the power off until the data transfer is completed. Any of the above operations during data transfer will disable the firmware update.

* Macintosh version of UploadFirmware requires Mac OS 8.6 to 9.2.

(2) Insert the CF card with the firmware into the camera and turn the Main Switch on.

The following message will appear on the LCD after the firmware update program activates.

When using the "UploadFirmware" utility, please be sure that data transfer is completed. Next step, open and close the CF card slot cover. Then, the firmware update program starts and the following message will appear on the LCD.

(3) Select [OK] with Quick Control dial of the camera and press the "SET" button.

If you select [Cancel] and press the "SET" button, the firmware update is cancelled.
If the message of "Execute Upgrade" does not appear, please return to Procedure (1) as the firmware is not copied correctly.

The first step in installing the new firmware is checking the currently installed firmware.

A message of [Checking Firmware] appears and the firmware currently installed is being checked. This step will take approximately 6 seconds.
An indicator (%) and a progress bar will appear during this step.
Do not press the shutter button during this step. Checking firmware will be cancelled by pressing the shutter button.

After checking the current firmware, both the current and the replaced versions will be displayed on the LCD as follows.

(4) Execute the firmware update after confirming the version to be installed, by selecting [OK] with Quick Control dial and pressing the "SET" button.

If you select [Cancel] and press the "SET" button, the firmware update is cancelled.

The following message will appear during firmware updating.

The update will take approximately 2 minutes.

Do not turn the power off during the firmware writing operation.
Do not open the CF card slot cover or press any camera button during the firmware writing operation.

When the update is completed, the following message will appear on the LCD.

(5) Complete the firmware update by pressing the "SET" button.

The firmware update is now completed. Format the CF card before using it again.

Verifying the firmware update

If firmware version is "1.0.4", updating is completed properly. To confirm the firmware version, turn the
Main Switch ON, and press the MENU button to display the menu. Turn the Quick Control Dial, and you will see the "Firmware Ver.1.0.x" at the end of the settings shown in yellow, which is the number of the firmware version. For more details, please refer to the instruction manual at page 32, 33 and 121.

If an ERROR message appears during the firmware update

In case the following message appears during the firmware update, please press the "SET" button and return to the beginning of the procedure. If you still have a problem, please contact the Canon Service Center in your region.

IMPORTANT!

IMPORTANT- READ THIS AGREEMENT CAREFULLY BEFORE CLICKING "I agree and download" AT THE BOTTOM OF THIS PAGE!

This License Agreement (the "Agreement") is a legal agreement between you and Canon Inc. ("Canon") under which Canon is providing the software program for version-up of the firmware of Canon’s digital camera products "EOS D60" (the "Software"). BY CLICKING "I agree and download" AT THE BOTTOM OF THIS PAGE, YOU ARE DEEMED TO AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT, DO NOT DOWNLOAD THE SOFTWARE. IN SUCH EVENT, YOU WILL NOT BE ABLE TO USE THE SOFTWARE

1. GRANT OF LICENSE: Canon grants you a personal and non-exclusive license to install the Software directly or through other medium such as hard disk or CompactFlash and use on Canon’s digital camera product "EOS D60" which you own.

You shall not assign, sublicense, sell, rent, lease, loan, convey or otherwise transfer to any third party, or copy, duplicate, translate or convert to another programming language the Software, except as expressly provided herein. You shall not alter, modify, disassemble, decompile or otherwise reverse engineer the Software and you also shall not have any third party to do so. You shall not modify, remove or delete a copyright notice of Canon contained in the Software.

Except as expressly provided herein, no license or right, express or implied, is hereby conveyed or granted by Canon to you for any intellectual property of Canon.

2. OWNERSHIP AND COPYRIGHT: The Software is copyrighted and owned by Canon. You agree and acknowledge that Canon transfers neither ownership interest nor intellectual property in the Software to you under this Agreement or otherwise, and that Canon retains all right, title and interest to the Software.

3. EXPORT RESTRICTIONS: You agree to comply with all applicable export control laws and regulations of the country involved, and not to export or re-export, directly or indirectly, the Software in violation of any such laws and regulations.

4. SUPPORT AND UPDATE: Canon, Canon’s subsidiaries and affiliates, their distributors and dealers are not responsible for maintaining or helping you in your use of the Software. No updates, bug-fixes or support will be made available to you for the Software.

5. DISCLAIMER: THE SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE SOFTWARE IS WITH YOU. SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU (AND NOT CANON, CANON’S SUBSIDIARIES AND AFFILIATES, THEIR DISTRIBUTORS AND DEALERS) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IN SUCH STATES WHICH DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES.

Canon, Canon’s subsidiaries and affiliates, their distributors and dealers do not warrant that the functions contained in the Software will meet your requirements or that the operation of the Software will be uninterrupted or error free.

IN NO EVENT SHALL CANON, CANON’S SUBSIDIARIES AND AFFILIATES, THEIR DISTRIBUTORS AND DEALERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITATION, LOSS OF BUSINESS PROFITS, LOSS OF BUSINESS INFORMATION, LOSS OF BUSINESS INTERRUPTION OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES) ARISING OUT OF THE SOFTWARE, USE THEREOF OR INABILITY OF USE THEREOF EVEN IF CANON, CANON’S SUBSIDIARIES OR AFFILIATES, THEIR DISTRIBUTORS OR DEALERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU IN SUCH STATES WHICH DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

CANON, CANON’S SUBSIDIARIES AND AFFILIATES, THEIR DISTRIBUTORS AND DEALERS SHALL HAVE NO OBLIGATION TO INDEMNIFY YOU AGAINST ANY CLAIM OR SUIT BROUGHT BY A THIRD PARTY ALLEGING THAT THE SOFTWARE OR USE THEREOF INFRINGES ANY INTELLECTUAL PROPERTY OF SUCH THIRD PARTY.

6. TERM: This Agreement is effective upon your clicking "AGREE" at the bottom of this page. You may terminate this Agreement by deleting the Software. This Agreement will also terminate if you fail to comply with any of the terms of this Agreement. In addition to Canon enforcing any of its legal rights, you shall then promptly delete the Software.

7. U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE: The Software is a "commercial item," as that term is defined at 48 C.F.R. 2.101 (Oct 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the Software with only those rights set forth herein. Manufacturer is Canon Inc./30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan.

8. SEVERABILITY: In the event that any provision of this Agreement is declared or found to be illegal by any court or tribunal of competent jurisdiction, such provision shall be null and void with respect to the jurisdiction of that court or tribunal and all the remaining provisions of this Agreement shall remain in full force and effect.

9. ACKNOWLEDGMENT: BY CLICKING "I agree and download" AT THE BOTTOM OF THIS PAGE, YOU SHALL BE DEEMED TO HAVE ACKNOWLEDGED THAT YOU HAVE READ THIS AGREEMENT, UNDERSTOOD IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT THIS AGREEMENT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF AGREEMENT BETWEEN YOU AND CANON CONCERNING THE SUBJECT MATTER HEREOF WHICH SUPERSEDES ANY PROPOSALS OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN THE PARTIES RELATING TO THE SUBJECT MATTER OF THIS AGREEMENT. NO AMENDMENT TO THIS AGREEMENT SHALL BE EFFECTIVE UNLESS SIGNED BY A DULY AUTHORIZED REPRESENTATIVE OF CANON.